Re: Issue on latest Clear Linux and ACRN on UP2 board

Tzeng, Tonny <tonny.tzeng@...>

Hi Tomasz,

Your `efibootmgr -v` output indicates the #3 entry will be picked up first, which is the fall back boot entry for Systemd-boot. Please change the order with `efibootmgr -o` option. You should also enter the UP2 BIOS to make sure the ACRN boot entry is the first option.


-----Original Message-----
From: acrn-users@... <acrn-users@...> On Behalf Of Tomasz Bursztyka
Sent: Tuesday, April 28, 2020 3:14 PM
To: acrn-users@...
Subject: [acrn-users] Issue on latest Clear Linux and ACRN on UP2 board


I cannot get ACRN hypervisor running on my setup:
- UPĀ² board (Celeron N3350)
- Clear Linux, fresh install, version 32910

I followed the documentation here:

However, once I rebooted I did not get the kernel message
[ 0.000000] Hypervisor detected: ACRN

I only get these:
[ 5.759483] ACRNTrace: acrn_trace: not support acrn hypervisor!
[ 5.766132] ACRN HVLog: acrn_hvlog: not running under acrn

So the hypervisor is not running.
There is no acrn related devices in /dev, I cannot start any VM obviously etc..

Here is the kernel cmd line:

[ 0.000000] Command line: initrd=\EFI\org.clearlinux\freestanding-
00-intel-ucode.cpio initrd=\EFI\org.clearlinux\freestanding-i915-
firmware.cpio.xz root=PARTUUID=05e27678-99d6-4bed-bbbe-d28cb026566a
quiet console=tty0 console=ttyS0,115200n8 consoleblank=0 cryptomgr.notests hvlog=2M@0x1FE00000 i915.avail_planes_per_pipe=0x01010F
i915.domain_plane_owners=0x011111110000 i915.enable_guc=0
i915.enable_gvt=1 i915.nuclear_pageflip=1 ignore_loglevel init=/usr/lib/systemd/systemd-bootchart intel_iommu=igfx_off
memmap=2M$0x1FE00000 no_timer_check no_timer_check noreplace-smp
rcu_nocbs=0-64 rcupdate.rcu_expedited=1 rootfstype=ext4,btrfs,xfs rootwait tsc=reliable rw

The EFI configuration seems legit, however:

# efibootmgr -v
BootCurrent: 0003
Timeout: 1 seconds
BootOrder: 0003,0005,0001
Boot0001 UEFI: Built-in EFI Shell VenMedia(5023b95c-db26-429b-
Boot0003* UEFI OS HD(1,GPT,f2d8aada-01a9-4c9c-86fe-
Boot0005* ACRN Hypervisor HD(1,GPT,f2d8aada-01a9-4c9c-86fe-
e.f.i. .u.a.r.t.=.b.d.f.@.0.:.1.8...1.

I switched the order to 0005,0003,0001 but it made no difference, and once I did: the bootorder had automaticaly changed back to 0003,0005,0001. Is this nominal?

The acrn.efi is from, which requested to do:

cp /usr/lib/acrn/acrn.nuc7i7dnb.industry.efi /usr/lib/acrn/acrn.up- apl01.industry.efi

So I did. (and installation seemed to go well.)

Any idea where the problem could be?

Join to automatically receive all group messages.